MikroElektronika mikroProg Manuel d'utilisateur

programming softwaremikroProg Suite™ for PIC® is a free software used for programming all of Microchip® microcontroller families, including PIC10®, P

Page 102. Quick startTo program your microcontroller with a desired .HEX le just follow these few steps:Before you begin, connect your device (

Page 11* Note that you can also load the HEX le by dragging and dropping it onto the mikroProg Suite™ for PIC® window.step 3 – Load .HEX step 4 – Bro

Page 12step 5 – Write HEXstep 6 – Progress barstep 7 – Finish upload01 0101Click Write to start programming the microcontroller.Progress bar displays

Page 130103020405Load .HEX leSave .HEX le under dierent nameReload .HEX leDisplay information about .HEX leClose mikroProg Suite™ for PIC®3. Menu

Page 14Figure 3-5: USB menuFigure 3-6: Info menuFigure 3-7: History windowFigure 3-8: Minimize optionWhen two devices are connected at the same time i

Page 15Figure 4-1: Cong windowAlong the right side of the main window, you may notice a CONFIG button. Click it to expand the main window with an add

Page 165. MCU Info windowA click on the MCU INFO button opens a window containing basic data about the selected microcontroller as well as voltage mon

Page 17The programming voltage (Vpp) is provided by the programmer during the programming procedure. Depending on the type of the microcontroller, the

Page 18Figure 5-2:MCU information sectionExample in Figure 5-2 shows information on the PIC18F45K22 microcontroller such as: microcontroller memory si

Page 19Figure 6-1: Options buttonFigure 6-2: Options window6. Advanced optionsClick the Options button, and a window containing Program/Verify Options

I want to express my thanks to you for being interested in our products and for having condence in MikroElektronika.The primary aim of our company is

Page 20Within the Program/Verify Options section it is possible to disable programming /verication of the microcontroller memory: CODE, Executive, DA

Page 217. Keyboard shortcutsand command line parametersKeyboard shortcutsAlt+E Erase the contents of the microcontroller memoryAlt+B Program memor

Page 22Example 01 mikroProg Suite for PIC.exe -w -pPIC18F45K22 -v -f”C:\somele.hex”This command is used for loading C:\somele.hex into the PIC18F45

DISCLAIMERAll the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual is to b

If you want to learn more about our products, please visit our website at www.mikroe.comIf you are experiencing some problems with any of our products

Page 3Introduction to 4mikroProg Suite™ for PIC® 4Main window 51. Installation 6step 1 – Start installation 6step 2 – Licence agreement

Page 4Introduction tomikroProg Suite™ for PIC®Program mikroProg Suite™ for PIC® is intended for programming PIC®, dsPIC® and PIC32® microcontrollers

Page 5Main window010203040506070809101112141513161817192001020304050607080910MCU family selection listMCU type selection listRead program from MCUVeri

Page 61. Installationstep 1 – Start installation 01Welcome screen. Click Next to proceede.01mikroProg Suite™ for PIC® setup executable can be

Page 7step 3 – Select userstep 2 – Licence agreement 01020102Carefully read the End User License Agreement.If you agree with it, click Next to procede

Page 8step 5 – Progress barstep 4 – Choose destination01020102Use the suggested destination folder or select a dierent installation path by clicking

Page 9step 6 – Finish installation 01Click the Finish button to close the Setup Wizard.01After the installation process is nished mikroProg Suite™ fo